3/15/2023 0 Comments Pfe automailer 5 plus![]() A minimum overlap or clearance of 5mm (3/16") is required between an insert edge and the innermost edge of the carrier envelope side seam. This can have a major effect on how well booklets load into a feed hopper and consequently the feeding efficiency. ![]() Booklets require a spine to edge thickness ratio of less than 1.25:1 for optimum running. Feeding of booklets can be particularly adversely affected by distortion. Care must be taken in the storage of inserts inadequate stacking by a supplier can result in curved edges and spines, causing inserts to seat poorly in the feed hopper. Inserts should be flat and free from distortion. Part loading of the hopper can overcome this but it will require more frequent loading. thicker on one side than the other) will not seat well in the feed hopper and this can affect feed and separation. Inserts should be dimensionally symmetrical for optimum running. Sandwiching a narrow insert between two wider ones may resolve this. If this difference in width is exceeded the insertion fingers will not cover the side edges of the narrow insert and cause an insertion problem. The maximum allowable width difference between inserts is 32mm (1¼ ). NOTE: Insert Requirements for Optimum Running Inserts should be sufficiently flexible to suit the transport path restraints. Technical Specification (cont.) Minimum clearance of insert pack inside envelope: Up to 3mm thick pack: Depth 6mm (1/4 ) Width 14mm (9/16 ) 3-6mm thick pack: Depth 10mm (3/8 ) Width 19mm (3/4 ) Total Pack thickness for insertion: 6mm (1/4 ) max. as for insert feeder) Folded length: 150mm (5 7/8 ) Thickness: 3mm (1/8 ) max. Datacard Turnover Interface Unit Document Sizes Width: 222mm (8.75 ) max. Hopper capacity: Up to 200 reply-paid envelopes or 100 2mm booklets. (upper hopper) See also notes on following page. for module 1 (either or both hoppers & OMR) 89mm (3 1 / 2 ) min. Insert Sizes - Dual Hopper & OMR Feeder Depth: 76mm (3 ) min. Hopper capacity: Up to 300 reply-paid envelopes or 150 2mm booklets. Technical Specification SECTION 1 TECHNICAL SPECIFICATION Form Sizes Insert Feeder Unit Insert Sizes - Single Hopper Depth: 76mm (3 ) min. Do not place surrounding furniture or other objects where your path may be obstructed. Ensure you have free access all round the machine for loading paper hoppers etc. Do not attempt to operate the machine with stationery outside the limits shown in the specifications. Avoid placing piles of stationery or other objects on top of the machine - they could topple off and create a hazard. Do not cover any vents or openings, or overheating may result. If any access cover safety switch fails allowing the machine to continue operating when the cover is opened, call a PFE authorised Service Engineer immediately. If damage to any cover has occurred, it must be replaced by a PFE authorised Service Engineer. Other types may use flammable propellants, which could result in fire or explosion. When cleaning sensors, use only non-flammable airdusters, such as supplied by PFE (part number E0070A). If service attention is required, call a PFE authorised Service Engineer. Do not attempt to dismantle any part of the machine, or remove any fixed covers - this could result in risk of electric shock or fire. When opening the covers, ensure that all moving parts have come to a halt before touching them. Keep loose clothing, long hair and jewellery clear of all moving parts. Do not try to use this machine until you have read these Operating Instructions and are fully conversant with its operation. This should be done by opening any of the covers. Hoppers 42 Setting the Separator Gap Operator Maintenance 44 Part Number K1216A Issue 2 December 2006 Ģ Safety Precautions Observe the following safety precautions at all times when running the Maximailer Plus Be sure you know how to switch the machine off in the event of an emergency. The Run Screen 10 To Change the User or Job 12 To Adjust Envelope Inserter 13 To Adjust Document Inserter The Setup Screen 17 Explanation 17 The List Box The OMR Code Screen The Barcode/Label Screen The Documents Screen The Envelopes Screen The Configuration Screen 27 Configuring the Inserter 27 Inserter Options for Inserter Unit 28 Document Options for Feed Unit 29 Feed Options for Feed Unit 30 Postage Options 32 Output Options (Batching) 33 Miscellaneous Options The Job Screen The Users Screen The Statistics Screen Running the Job Setting up the Machine 42 Loading the Paper & Env. Machine Layout Guide Description of Machine Parts Identification 8 3. 1 Contents Maximailer Plus Page Safety Notes 2 1.
0 Comments
Leave a Reply. |
AuthorWrite something about yourself. No need to be fancy, just an overview. ArchivesCategories |